Amana AM33LP-P Příručka pro použití a péči

AMANA®FOUR BURNER GAS GRILL w/ REAR BURNERAssembly/Installation Instructions and Use & Care GuideFor questions about features, operation/performan

4. Repeat step 1-2 to install the cart side right in position.5. Place the cart back onto the grill cart base. Place two wheel channel assembly bolts

116. Place the cart middle shelf onto the cart base.7. Use three (3) self-tapping screws to secure the cart middle on the cart base.8. Use three (3) s

129. Use two (2) self-tapping screws to secure the middle bracket onto the cart side left.Note: Install the self-tapping screws from outside of cart s

1. Take the side burner package out from inside the grill head.2. Tilt the grill head on its back and loosen the four (4) grill mounting bolts so that

ASSEMBLY INSTRUCTIONSStep 4: Assemble DrawersA. HandleB. Drawer front faceC. Phillips head screwsD. Drawer trayE. Self-tapping screws14ABCED1. With a

ASSEMBLY INSTRUCTIONSStep 4: Assemble Drawers (Cont.)ABC15A. Drawer assemblyB. Slide attached to the drawerC. Slide rail assembly on the cart5. Align

ABCASSEMBLY INSTRUCTIONSStep 4: Assemble Drawers (Cont.)167. Take the other drawer, align the slides (attached to the drawer) with the front ends of t

ASSEMBLY INSTRUCTIONSStep 5: Assemble Cart Door1. Remove the two phillips pan head screw on the cart door handle and use these two screws toinstall th

18ASSEMBLY INSTRUCTIONSStep 6: Assemble Side Shelf Left1. Loosen the Four (4) 5/16-24 hex head screws located on the left grill side.2. Attach the lef

19ASSEMBLY INSTRUCTIONSStep 7: Assemble Side Burner Cover & Igniter Module1. Remove the brass burner cap attached with tape along with side burner

TABLE OF CONTENTS2OUTDOOR GRILL SAFETY...3-4U

1. Loosen the four (4) 5/16-24 hex head screws.2. Attach the side burner shelf by inserting the four (4) screws on the side of the grill head intothe

ASSEMBLY INSTRUCTIONSStep 9: Assemble the Side Valve1. Using a Phillips screwdriver, remove the 2 screws from the side burner valve assembly.2. Push t

ASSEMBLY INSTRUCTIONSStep 10: Assemble the Side Burner Casting1. Remove the two phillips pan head screws from the side burner casting.2. Angle the sid

ASSEMBLY INSTRUCTIONS1. Use the two (2) screws removed in step 1 on page 22 to secure the head of side burner castingon the rear bracket.2. Use the tw

ASSEMBLY INSTRUCTIONSStep 11: Assemble Igniter ModuleAA. Igniter moduleB. Side burner igniter wireC. Main burner igniter wiresD. Back IR burner ignite

ASSEMBLY INSTRUCTIONSStep 12: Assemble the Side Burner Accessories1. Center the brass burner cap on top of the side burner head.2. Place the side burn

ASSEMBLY INSTRUCTIONSStep 13: Assemble the Drip Pan1. Pull out the top drawer.2. Open the right cart door.3. Slide the drip pan onto the drip pan guid

27ABCA. Flavor gridsB. Main cooking gratesC. Bread warming rackD. Back Ir burner wind sheild1. Insert the flavor grids into the cutouts with triangle

28INSTALLATION REQUIREMENTSSelect a location that provides minimum exposure to wind and traffic paths. The locationshould be away from strong draft ar

Product Dimensions53.625”(136.3cm)45”(114.4cm)33.875”(86.1cm)32”(81.3cm)13.125”(33.4cm)21”(53.3cm)20.2”(51.3cm)Observe all governing codes and ordinan

OUTDOOR GRILL SAFETYYour safety and the safety of others are very important.We have provided many important safety messages in this manual and on your

Gas Supply Line Pressure TestingTesting above ½ psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):The grill and its individual shutoff valve must be dis

Check the burnersThe burners are tested and factory-set for most efficient operation. However, variations in gas supplyand other conditions may make m

32OUTDOOR GRILL USEControl PanelOFFPUSH&TURNHLMOFFPUSH&TURNHLMOFFPUSH&TURNHLMBCDFEA. Back IR burner control knobB. Left burner control kno

Using Your Outdoor Grill (cont.)Manually Lighting Grill1. Do not lean over the grill.2. Remove the manual lighting extension and attach a match to the

Using Your Outdoor Grill (cont.)Using Your Rotisserie BurnerThe grill rotisserie burner is designed to cook items from the back using infrared heat. T

Using Your Back IR Burner (cont.)PROTECTION OF INFRARED BURNERSThe burners of your grill are designed to provide a long life of satisfactory performan

TIPS FOR OUTDOOR GRILLING36Before Grilling Thaw food items before grilling. Lightly oil the grill grates or the food when cooking low-fat cuts of me

OUTDOOR GRILL CAREReplacing the Igniter BatteryIf igniters stop sparking, the battery should be replaced.1. Unscrew igniter button cap counter clockwi

38OUTDOOR GRILL CARE (Cont.)General Cleaning (Cont.)WARMING SHELFCleaning Method: Liquid detergent or an all-purpose cleaner. Rinse with clean water

39OUTDOOR GRILL CARE (Cont.)General Cleaning (Cont.)DRIP PAN AND SHELFIMPORTANT: The drip pan should only be removed when grill is completely cool.The

IMPORTANT SAFETY INSTRUCTIONSIMPORTANT: This grill is manufactured for outdoor use only. For grills that are to be used atelevations above 2000 ft (60

TROUBLE SHOOTINGGrill will not light Is the 20 lb LP gas fuel cylinder valve turned off?Turn the 20 lb LP gas fuel cylinder on. Is the grill properl

41REPLACEMENT PARTSHood Assembly Front Face OverlayFCTG3308001 FCTG33080061 set 1 setHood Handle Amana LogoFCTG3308002 FCTG26080081 pcs 1 pcsTemp Guag

42Side Burner Griddle Cart side rightFCTG3308025 FCTG290800161 set 1 setCart back Wheel channel leftFCTG3308010 FCTG29080171 set 1 setCart door right

Side Burner Right Assy. Side burner igniterFCTG3308022 FCTG26080301 set 1 pcsIgniter Module 6 polesSide Burner ValveFCCS3308012 FCTG26080321 pcs 1 pcs

AMANA® is a registered trademark of Maytag Corporation or its related companies and is used under license toSure Heat Manufacturing© 2008.All rights r

1. Using a utility knife, cut the tape to open top flaps ofcarton.2. Remove Assembly/Installation Instructions and Use andCare Guide.3. Remove the lar

Assembly Hardware Supplied 40 - self-tapping screws 4 - sunken head self-tapping screws 1 - Side burner knob with bezel 1 - “AA” batteryNOTE: Othe

ASSEMBLED GRILL VIEWACDEFGHJIKA. Control knob: main burnersB. Control knob: back IR burnerC. Side shelfD. Grilling/cooking surfaceE. Bread warming rac

ASSEMBLY INSTRUCTIONSStep 1: Assemble Wheel Channels1. Remove the four (4) caster assembly nuts and two (2) bolts from the wheel channel assemblies.No

Step 2: Assemble Grill Cart1. Place the cart side left onto the two (2) outer caster assembly bolts, make sure the largeflange is toward the front of